• search

Airbag Module Location

For part location in vehicle select Make, Model, Year

GMC
  1. Select Make...
  2. ACURA
  3. ALFA ROMEO
  4. AUDI
  5. BMW
  6. BUICK
  7. CADILLAC
  8. CHEVROLET
  9. CHRYSLER
  10. DAEWOO
  11. DODGE
  12. EAGLE
  13. FERRARI
  14. FIAT
  15. FISKER
  16. FORD
  17. GEO
  18. GMC
  19. HONDA
  20. HUMMER
  21. HYUNDAI
  22. INFINITI
  23. INTERNATIONAL
  24. ISUZU
  25. JAGUAR
  26. JEEP
  27. KIA
  28. LAMBORGHINI
  29. LAND ROVER
  30. LEXUS
  31. LINCOLN
  32. LOTUS
  33. MASERATI
  34. MAZDA
  35. MCLAREN
  36. MERCEDES
  37. MERCEDES-BENZ
  38. MERCURY
  39. MINI
  40. MITSUBISHI
  41. MV-1
  42. NISSAN
  43. OLDSMOBILE
  44. PLYMOUTH
  45. PONTIAC
  46. PORSCHE
  47. RAM
  48. SAAB
  49. SATURN
  50. SCION
  51. SMART CAR
  52. SUBARU
  53. SUZUKI
  54. TESLA
  55. TOYOTA
  56. VOLKSWAGEN
  57. VOLVO
  58. WINNEBAGO
  59. WORKHORSE
SIERRA
  1. Select Model...
  2. 1500
  3. 2500
  4. 3500
  5. ACADIA
  6. C3500
  7. C4500
  8. C5500
  9. CANYON
  10. DENALI
  11. ENVOY
  12. JIMMY
  13. SAFARI
  14. SAFARI VAN
  15. SAVANA
  16. SIERRA
  17. SONOMA
  18. SUBURBAN
  19. TERRAIN
  20. TOPKICK
  21. VAN
  22. YUKON
2005
  1. Select Year...
  2. 2019
  3. 2018
  4. 2017
  5. 2016
  6. 2015
  7. 2014
  8. 2013
  9. 2012
  10. 2011
  11. 2010
  12. 2009
  13. 2008
  14. 2007
  15. 2006
  16. 2005
  17. 2004
  18. 2003
  19. 2002
  20. 2001
  21. 2000
  22. 1999
  23. 1998
  24. 1997
HOW TO: Removal Videos
Instructional Video Place your reset order

Failure to follow instructions below may result in the accidental deployment of “air bag”, “seat belt”, which increases the risk of serious personal injury or death.

  • Never probe the electrical connectors on air bag or seat belt.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

To remove your airbag control module, follow these steps:

  1. First find the srs computer module. In most cars it is under the center console that is between the two front seats, or center of the dash on the floor. In most GM cars it is under the driver or passenger seat.
  2. Disconnect the positive battery cable and wait 3 min.
  3. You are now safe to unplug the airbag control module harness wiring plugs.

To install your airbag control module:

  1. All airbag srs components must be installed and connected properly before installing the airbag control module. This includes air bags, seat belts, clock spring and impact sensors.
  2. Disconnect the battery and bolt down the module and then connect the harness wiring plugs.
  3. Wait 3 minutes before installing the airbag module in the vehicle.
  4. Bolt down module with all bolts and then connect harness plugs. (if not then, could deploy roof airbags and seat belts)
  5. Vehicle needs to be flat on the ground. Not elevated on a jack or lift. (if not then, could deploy roof airbags and seat belts)
  6. Reconnect battery cables.

Disclaimer: The buyer assumes all risks associated with removing, installing, and usage of a re-manufactured part(s). If you have additional questions please call us at 888-779-9029 or submit a request.

Place your reset order
×